Zlinx I/O Module - Zlinx Wireless Modbus I/O

Zlinx I/O Module - Wireless Modbus I/O | Faster And Better Than Ever

• Improved Latency - Very low I/O latency allows real time control and monitoring.
• Exception Reporting - In Modbus mode, allows the reporting of possible problems with connected devices.
• Fail Safe - Allows you to set your I/O to a safe state in the event of a communication failure.
• Calibration - Calculates correction factors to make I/O values more accurate or to better match a sensor.
• Communications Failure Alarm - Allows the first DO to be configured as a COM failure alarm indicator.
• Peer-to-Peer I/O Configuration - One to one I/O mapping of 2 identical systems. Allows remote control of analog and digital I/Os.
• Inverter Outputs - Allows flexibility in the logic to control output devices.
• Monitor - You can use the Zlinx Manager Software to monitor your I/O.

Add Wireless I/O to Any Modbus System

• Connects directly to analog, digital and temperature inputs and outputs
• Point to point/multi-point wire replacement
• Exandable, modular design
• Modbus compatible
• Class 1, Div 2 Approved

Modbus Appliction (Peer to Multi-Peer)

Seamlessly add wireless I/O to any Modbus application. Modbus is the most widely supported I/O protocol worldwide for PLC's to HMI's and PC based software applications. With Zlinx Wireless I/O you can now bring wireless remote I/O into any Modbus system. Simply connect a Zlinx modem to an RS-232 or RS-485 port of the Modbus master and it can now poll up to 150 wireless I/O nodes - each node can be configured for 8 to 48 I/O points.
 
 

Specifications

Digital Inputs

• Voltage Range: 0 to 48 VDC
• Low Voltage (0): 0.8 V maximum
• High Voltage (1): 4.0 V minimum
• Pull Up Current: 38 micro-amps
• Frequency Input: 2 DI inputs per module Software selectable as frequency counters,0 to 5 KHz range.

Digital Outputs

• Voltage Range:
  • 10 to 40 VDC (Sourcing)
  • 0 to 48 VDC (Sinking)
  • 40 mA per output

Relay Outputs

• Number of Relays: 8
• Type: C -normally open & normally closed
• Output Connection: 3.5mm removable terminal block (2 per output)
• Common Connection: 3.5mm removable terminal block
• Ratings: 250VAC @ 8A, 30VDC @5A (maximum per bank of 4 as grouped on the label)

Radio Properties (SR Models)

• Frequency: 2.4 GHz
• Output Power : 100 mW
• Receiver Sensitivity: -102 dbm
• Antenna: The included antenna is a 4.25 inch omni-directional with RPSMA connector. (p/n ZZ24D-ANT1)

Radio Properties (2.4 GHz MR Models)

• Frequency: 2.4 GHz
• Output Power: 50mW
• Receiver Sensitivity: 105 dbm @ 9.6K
• Antenna: The included antenna is a 4.25 inch omni-directional with RPSMA connector. p/n ZZ24D-ANT1

Radio Properties (900 MHz MR Models)

• Frequency: 900 MHz
• Output Power: 100 mW
• Receiver Sensitivity: -100 @ 9.6K
• Antenna: The included antenna is a 6.5 inch omni-directional with RPSMA connector. p/n ZZ9D-ANT1

LED Indicators

• Receive Signal Strength:
  • Tri-color – Off = No Signal
  • Red = Weak Signal
  • Yellow = Medium Signal
  • Green = Strong Signal
• RF Data:
  • Green – Blinks with TD or RD
  • Off = No Data
• Local Bus Data:
  • Green – Blinks with TD or RD
  • Off = No Data
• Power:
  • Red – On = Power applied
  • Off = No Power

Analog Inputs and Outputs

• Ranges: 0 to 10 VDC or 0 to 20 mA ZZ-4AO-2 is an active current source. All others are passive
• Resolution: 12 Bit
• Input Accuracy: 0.2% full scale reading typical
• Output Accuracy: 0.27% full scale reading typical
• AI Load Resistance: 100 Mega Ohms when configured for voltage input 250 Ohms when configured for current input
• AO Max Output Current: 1 mA when configured for voltage output.
• AO Max Load 450 Ohms when configured For current output @ 12V

RTD Inputs

• Number of RTD: 4
• Wire Configuration: 2, 3, and 4 wire
• Type: PT100, PT1000 (Optimized for temperature coefficient of 385 C), Cu10 (Optimized for temperature coefficient of 427 C)
• Input Connection: 3.5mm removable terminal block (4 per output)
• Temperature Range:
  • PT100 = (-) 200 to (+) 650 C
  • PT1000 = (-) 200 to (+) 100 C
  • Cu10 = (-) 100 to (+) 260 C
• Resolution: 0.1C cross at (-) 40 to (+) 80 C
• Accuracy @ 25 C: (+/-) 0.5 C typical
• Accuracy (-)40 to (+) 80C (+/-) 2.0 C maximum

Radio Properties (900 MHz LR Models)

• Frequency: 900 MHz
• Output Power: 1W
• Receiver Sensitivity: -100 dbm @ 115.2 K, -110 dbm @ 9.6 K
• Antenna: The included antenna is a 6.5 inch omni-directional with RPSMA connector p/n ZZ9D-ANT1

Radio Properties (868 MHz LR Models)

• Frequency: 868 MHz
• Output Power: 315 mW
• Receiver Sensitivity: -112 dbm
• Antenna: The included antenna is a 6.5 inch omni-directional with RPSMA connector p/n ZZ9D-ANT1

Environmental

• Operating Temperature
  • ZZ-8DO-R -40 to 55°C (-40 to 131°F)
  • All Others -40 to 80°C (-40 to 176°F)
• Maximum Ambient Air Temp
  • ZZ-8DO-R 55°C (131°F)
  • All Others 80°C (176°F)
• Storage Temperature -40 to 85°C (-40 to 185°F)
• Operating Humidity 0 to 95% Non-condensing
• Enclosure Plastic IP30
• Mounting 35mm DIN Rail
• Expansion 1 Base Module supports up to 6 Expansion Modules
• Dimensions 1.2 x 3.7 x 5.0 in (2.9 x 9.3 x 12.7 cm)